Search / Korean Journal of Chemical Engineering
Korean Chemical Engineering Research,
Vol.57, No.5, 611-619, 2019
흡열연료 종류와 촉매 성형 방법에 따른 분해특성과 코크 생성에 관한 연구
Study on the Fuel Decomposition Characteristics and Coke Formation by Type of Endothermic Fuel and Method of Catalyst Molding
본 연구에서는 흡열연료의 종류와 촉매의 성형 방법에 따른 연료의 분해특성 및 코크 생성에 대하여 분석하였다. 실험에 사용된 연료는 methylcyclohexane (MCH), n-dodecane 그리고 exo-tetrahydrodipentadiene (exo-THDCP)이며, 백금을 담지한 USY720에 압력만을 가하여 제조한 disk 형태, binder와 silica solution을 혼합하여 제조한 pellet 형태의 제올라이트를 촉매로 사용하였다. 성형 방법에 따른 촉매의 특성은 X-ray 회절분석법(XRD), 주사전자현미경(SEM), 질소흡탈착등온선 그리고 암모니아 승온탈착분석법을 통해 분석하였으며, 연료가 초임계 상태로 존재할 수 있는 고온 고압의 조건(500 °C, 50 bar)에서 반응을 진행시킨 후에 생성된 혼합물은 가스 크로마토그래프 질량분석계(GC-MS), 촉매에 생성된 코크는 열중량분석기를 사용하여 분석하였다. 이와 같은 분석을 수행한 결과, 반응 후 생성물의 조성은 연료를 구성하는 화합물의 구조에 따라 크게 차이를 보였다. 또한, 촉매의 성형 방법에 따른 결정성이나 표면 특성의 변화는 미미하였으나, 비교적 큰 변화를 보인 산점과 기공 특성이 생성물과 코크 생성량 및 조성의 변화에 영향을 주는 것으로 확인되었다.
This study was carried out to investigate fuel decomposition characteristics and coke formation according to types of endothermic fuels and methods of catalyst molding. Methylcyclohexane (MCH), n-dodecane, and exotetrahydrodipentadiene (exo-THDCP) were used as the endothermic fuels. As a catalyst, USY720 supported with platinum was used. It was manufactured by only using pressure to disk-type, or pelletized with a binder and a silica solution. The characteristics of the catalysts according to the molding method were analyzed by X-ray diffraction analysis, scanning electron microscopy, nitrogen adsorption-desorption isotherm, and ammonia temperature programmed desorption analysis. The reaction was carried out under conditions of high temperature and high pressure (500 °C, 50 bar) in which the fuel could exist in a supercritical state. The product was analyzed by gas chromatograph/mass spectrometer and the coke produced by the catalyst was analyzed by thermogravimetric analyzer. After the reaction, the composition of the products varied greatly depending on the structure of the fuel. In addition, the crystallinity and surface properties of the catalysts were not changed by the method of catalyst molding, but the changes of the acid sites and the pore characteristics were observed, which resulted in changes in the amount and composition of products and coke.
[References]
  1. Sobel DR, Spadaccini LJ, ASME 1995 International Gas Turbine and Aeroengine Congress and Exposition, June, Houston(1997).
  2. Huang H, Sobel DR, Spadaccini LJ, 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit, July, Indianapolis(2002).
  3. Granata S, Faravelli T, Ranzi E, Combust. Explos., 132(3), 533, 2003
  4. Kim J, Park SH, Chun BH, Jeong BH, Han JS, Kim SH, Catal. Today, 185(1), 47, 2012
  5. Gerasimov GY, Losev SA, J. Eng. Phys. Thermophys., 78(6), 1059, 2005
  6. Edwards T, Maurice LQ, J. Propul. Power, 17(2), 461, 2001
  7. Daniau E, Bouchez M, Bounaceur R, Battin - Leclerc F, Marquaire PM, Fournet R, 12th AIAA International Space Planes Hypersonic Systems Technologies, December, Norfolk(2003).
  8. Edwards T, 31st Aerospace Sciences Meeting, January, Reno(1993).
  9. Qu SD, Liu GZ, Meng FX, Wang L, Zhang XW, Energy Fuels, 25(7), 2808, 2011
  10. Liu GZ, Zhao GL, Meng FX, Qu SD, Wang L, Zhang XW, Energy Fuels, 26(2), 1220, 2012
  11. Xing Y, Fang WJ, Xie WJ, Guo YS, Lin RS, Ind. Eng. Chem. Res., 47(24), 10034, 2008
  12. Deng HW, Zhang CB, Xu GQ, Tao Z, Zhang B, Liu GZ, J. Chem. Eng. Data, 56(6), 2980, 2011
  13. Edwards T, Combust. Sci. Technol., 178(1-3), 307, 2006
  14. Nakra S, Green RJ, Anderson SL, Combust. Flame, 144(4), 662, 2006
  15. Cooper M, Shepherd J, 39th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, July, Huntsville(2003).
  16. Tian YJ, Qiu Y, Hou X, Wang L, Liu GZ, Energy Fuels, 31(11), 11987, 2017
  17. Kim J, Hyeon DH, Park SH, Chun BH, Jeong BH, Han JS, Kim SH, Catal. Today, 232, 63, 2014
  18. Guisnet M, Magnoux P, Appl. Catal., 54(1), 1, 1989
  19. Holland BT, Abrams L, Stein A, J. Am. Chem. Soc., 121(17), 4308, 1999
  20. Janssen AH, Schmidt I, Jacobsen CJH, Koster AJ, de Jong KP, Microporous Mesoporous Mater., 65, 59, 2003
  21. Tao YS, Kanoh H, Kaneko K, J. Phys. Chem. B, 107(40), 10974, 2003
  22. Ogura M, Shinomiya SY, Tateno J, Nara Y, Kikuchi E, Matsukata H, Chem. Lett., 29(8), 882, 2000
  23. Lai WC, Song C, Fuel Process. Technol., 48(1), 1, 2006
  24. Song CS, Lai WC, Schobert HH, Ind. Eng. Chem. Res., 33(3), 548, 1994
  25. Wohlwend K, Maurice L, Edwards T, Striebich R, Vangsness M, Hill A, 35th Joint Propulsion Conference and Exhibit, June, Los Angeles(1999).